ABCDEFGHIJKLMNOPQRSTUVWXYZ
1
Revision DateChange Description
2
5/8/2018Alinged on 260p connector.
3
5/8/2018
remove hbled signal. Will keep this onboard mezzanine. Instead will use BOOT_IND#, active low signal indicating SOC has booted.
4
5/8/2018lowered UART total interfaces to 4x. 2x of them have RTS/CTS signals
5
Fixed the 1.8v eSPI or 3.3v for LPC
6
added net vbus sense and fixed net names, took away from a GPIO. USB2APWREN_GPIO
USB2BVBUSSNS_GPIO
USB2AVBUSSNS_GPIO
7
5/14/2018Changed net names to better describe net names
8
5/14/2018Changed two UART primary flow control signals to secondary function for GPIOS
9
6/12/2018Fixed netname priority for GPIO_RGMIIMDC and GPIO_RGMIIMDIO to have GPIO come first
10
6/13/2018Removed 2nd JTAG interface.
11
6/13/2018Moved USB host and USB device into its own general function for general pin count tab
12
6/13/2018Changed USB host net name from USB2AVBUSSNS to USB2AOC (Over current)
13
6/13/2018Reduced UARTs from 5 to 3. Moved the 4 extra signals to GPIO
14
6/13/2018Changed a UART netname to "CONSOLE" instead of UART
15
6/13/2018Increased to 16 I2C bus's. 4 are now secondary function instead of GPIOs.
16
6/14/2018Added quad mode support for both FW SPI and SPI1 interface. SIO[0:3] support as secondary function
17
6/15/2018Fix net naming errors for 1GbT signals
18
6/18/2018IO0/MOSI and IO1/MISO per standard - switched the SPI SIGNALS
19
6/21/2018
Changed a few descriptions, updated SIOPWREQ to SIOPME. Swapped PECI signals (wrong descriptions; only these were swapped)
20
7/4/2018Added column for runBMC aspeed naming on schematic
21
7/5/2018Removed reset from PWRGD. This is an input only for monitoring PSUs
22
7/5/2018SIO netnames need to have a "#" to reflect active low
23
8/14/2018Removed active low "#" for INDICATOR
24
8/14/2018Changed pinout reordering
25
8/14/2018INDICATOR is secondary option instead of primary
26
8/14/2018BMC_RST_N_CONN to BMC_RESET#
27
8/14/2018Add secondary function for KLUDGE as GPIO
28
8/14/2018Addended the net names that had VDD with _STBY
29
8/15/2018Moved Indicator to pin 109
30
8/15/2018SIOPWREQ was actualyl SIPME#
31
8/15/2018229, 231, and 241, 243 pins were swapped due to routing concenrs. Planning to swap these back for consitency.
32
9/17/2018
For SYSSPI signals we have made these primary function (GPIO is second function). The Indicator and WP signals have been moved
33
9/26/2018
Added secondary functions for GPIOs. These will be UARTS (RX, TX). Pins 144, 146, 148, 150 are updated on pinout. Pinout namings also updated
34
10/2/2018Removed secondary functionality for FWSPI pins; now act as FWSPI only (no GPIO secondary or primary function)
RGMIIRXCK for connector no longer has GPIO functionality
35
10/18/2018Added pinout for MiniSAS HD Connector on BUV
36
11/15/2018Changed Pin 2 from VDD_1V8_STBY to VDD_IO_REF. This is now an output voltage used for reference i/o, low current
37
11/15/2018Updated the direction for the pinout naming tab.
38
11/15/2018Changed USB2A primary descrioption as host
39
11/15/2018Changed USB net names to include HD (host) and D (Device) to be more descriptive
40
11/15/2018Changed BMCLPC3V3_BMCESPI1V8 to VDD_LPC3V3_ESPI1V8
41
11/15/2018
For runBMC_v2_260p_sodimm_pinouts, for System SPI, added IO0 to MOSI and IO1 to MISO (these changes were in the pinout naming but not in the sodimm pinout)
42
11/15/2018Added System SPI pins to the runBMC_pinout_naming sheet (they were missing before), 4 GPIOs were removed
43
11/15/2018Added UART3 & UART4 TX&RX pins, removed 4 GPIOs
44
11/15/2018Removed hardware flow control for UART1 & UART2, 4 GPIOs were added
45
11/15/2018Removed SIOPME signal, 1 GPIO added
46
11/15/2018
Renamed "Primary" and "Secondary" to "Function 1" and "Function 2", since we are now describing two types of pins; dedicated function and dual function
47
11/15/2018ADC [8-15] is GPI only.
48
11/15/2018
Changing the following GPIOs to GPO's only. GPIO_SPI1_IO2, SYSMISO_GPIO, SYSMOSI_GPIO, SPI1MISO_GPIO, SPI1MOSI_GPIO, UART1TX_GPIO to only be GPO
49
11/15/2018Back annotation of runBMC_v2_260p_sodimm_pinouts to make sure GPIOs are in ascending order
50
11/29/2018Change PECI pin to have no alternate functionality (on General Pin Count tab)
51
11/29/2018
I2C13 is connected to ID FRU, so I2C13 should not be dual function. Updated General Pin Count Tab & runBMC_pinout_naming tab
52
11/29/2018Removed SIOONCTRL from General Pin Count & runBMC_pinout_naming
53
12/8/2019Added GPIO as 2nd function for RGMIIRXCK
54
12/8/2019Removed duplicate UARTs in GPIOI blocks for UART3 and UART4
55
12/8/2019Added clear description for USB host/device pinout description
56
1/9/2019Changed VDD_IO_REF netname to VDD_RGMII_REF
57
1/10/2019Locked Revision 1.0!!
58
2/21/2019UNLOCKED
59
2/21/2019Changed some color scheming in the runBMC_v2_260p_sodimm_pinouts tab to be higher contrast
60
4/15/2019Changed Kludge to CPU_RST#. CPU_RST# is the PCH reset or AMD/CPLD reset output
61
5/7/2019Changed Klugde_GPIO65 to RESERVED_GPIO65. Removed Kludge language
62
8/6/2019
Added Pass-Through pins to some GPIOs, I2C9 is now the interal FRU bus. This means GPIOs had to be incremented by 2, change on pins 47 to 183
63
8/6/2019Locked Revision 1.4
64
1/24/2021Draft of v1.5
65
1/24/2021Added new tab for v1.5 pinout proposal and changelist discussion
66
1/24/2021Change pin name from CPU_RST# to PLT_RST#
67
1/24/2021Add pin95(GPIO63) to be BMC_PWRGD(output)
68
1/24/2021Add one more reset input pin on pin93(GPIO61) as PFR_RST#
69
1/24/2021Add SD interface (pin 141,143,187,189,199,201,48,50)
70
1/24/2021Add I3C interace (pin 123,125,205,207,128,130,134,136)
71
1/25/2020Updated Changelist Discussion Tab
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100